| |
|
| Here is the pic, you can clic it to
see all the flaws in 1024x768's resolution. the natural
light was unequal on Elle's face and the exposure
of the camera was bad, so this pic has some big and
obvious flaws. |
 |
| I should give the good color to the
skin where it's shiny and burned ; and i should suppress
the parasitic hairs... |
 |
| Here are all the correctings i should
do ... What a big job to do ! |
 |
| How to clean the parasitic hairs
? Begin by zooming in the area of the face to
clean... |
 |
| Select the tool figured by a small trowel. |
 |
|
In its configuration's window, select the width
of the tool. Have some tries with this parameter.
(one tip : average 3 times the width of the scratch
!)
|
 |
Click the scratch (hair) and stretch
your selection.
One tip : proceed centimeter by centimeter, or maybe
5 millimeters by 5 mms. |
 |
|
Then release the click and the tool does the job...
Not bad isn't it ;) ?
It is important to proceed by small selections,
particulary with complex pics with a lot of colors
and gradation of colors ../..
|
 |
because an average is calculated to
fill in your selection, so a small selection allow
the relevance of this average with colors.
Have some tries ! |
 |
| This tool applies to any type of scratches,
and to ugly points and to all the linear flaws... |
 |
| Selection of a ugly line in the pic.
|
 |
And cleaning.
If you make a mess, use CTRL + Z to cancel your last
clic. |
 |
|
Job's done ! the remaining hairs are too much dense
for beeing cleaned with this tool. Now we will see
how to clean them.
We must select the best color of the nearest skin
and paint the hairs with this color to clean them.
|
 |
| |
|
|
Select the "pipette" tool to memorize
a color by clicking an area with the good color.
Tips : select the foreground color with a left
clic and a background color with a right clic.
|
 |
| I clicked and the color's values are
shown. |
 |
| Then select the "paintbrush"
tool. |
 |
In its configuration window, select
the size of the brush (rounded shape = like a spray
or an aerograph).
Another important parameter is the opacity : a value
of 50 is good to begin, the painting will be half
transparent. |
 |
|
After maybe 100 clics we can see the final result.
I deleted the hairs so that they follow the curve
of her cheek.
I have often selected some new colors with the pipette
tool and used the Brush tool, playing with its parameters
(size and opacity).
It's a patience's game.(clickable pic for 1024x768's
resolution)
|
 |
It is the same method for the forehead's
shiny area :
- Pipette tool to select the color.
- Brush to apply the color. |
 |
| But i used a bigger size of brush for
the forehead (29) because the area to paint is bigger.
|
 |
| Work in progress with the forehead... |
 |
|
Forehead is done.
I used the brush with the following parameters
:
- size from 10 to 30 pixels.
- Opacity from 40 to 55 %. (40 is more transparent)
|
 |
After tens of clics, i modifyed the
cheek and the chin. We can see that it can look like
a person who has used too much make-up :D.
If we don't like, we need to use a filter to add some
noise. |
 |
|
Here the final result, you can click it for a 1024x768's
resolution.
I did not changed the lip, but have cleaned all
the hairs on her chest.
|
 |
| |
|
| |
|
| |
|
| |
|
